Do your once-durable faucets wobble or move? There may be a loose screw or a worn-out o-ring inside the head/base or handle. You will discover the problem once you learn how to tighten a kitchen faucet handle and faucet head.
A kitchen faucet aids in completing many tasks, and it should not wobble or be almost loose. A loose or wobbly kitchen faucet causes major problems like water leakage, mold development, rotting, and water pressure that damages plumbing pipes. Analyzing your faucet fixture, visiting the hardware store for the tools, and following the instructions to repair it are three simple steps to combat this concern.
Table of Contents
What Do I Need?
Preparation is the first step in this DIY project; the wrong items gathered will make it more challenging than need be. What you will need depends on whether the problem is a loose faucet handle or a loose faucet base. There are no easy steps, but the right tools will lessen the stress, especially if this is your first time.
- A basin wrench, adjustable wrench, adjustable pliers, vice grips, or masking tape
- Safety goggles or safety glasses
- A flashlight
- A mini knife
- Hand gloves
- A knife, Phillips head screwdriver, or flathead screwdriver
- A hex head wrench, pipe wrench, Allen key, or Allen wrench
- Safety glasses or safety goggles
- A flashlight
- An old toothbrush
- A new o-ring and rubber seals
- Plumber’s grease with heatproof silicone
Kitchen Faucet Mechanics
In the kitchen, the faucet fixture is at the opposite end of where you’re standing. One of the first things to do is learn where the handle and base tighten. The base nut is likely under the sink; the handle screw is underneath the decorative cap.
For the base, use a flashlight to see how the bottom and top connect. Determine if the source is a kitchen faucet nut, a flathead screw, or a Phillips screw. While you’re under there, locate the cold water valve and the hot water valve so you can turn them off during the repair.
For the handle, is it a double-handle or single-handle kitchen faucet, and do you know if one or both is the problem? Does a hex head screw, a flathead screw, or a Phillips screw tighten the handles? Also, check to see if the o-ring needs a replacement on handles because a worn-out one causes a leaky kitchen faucet.
If the faucet is a Moen faucet, a loose Moen kitchen faucet base uses the same steps as traditional bases. However, a Moen kitchen faucet handle knob differs from traditional handles, so there are separate instructions for repairing them.
On the knob, the cap is on the back, and the screw is inside the handle. For the single handle kitchen faucet keep the knob connected to the base as you screw it with a key wrench. Because there is room for error, the best option is to call a professional plumber to handle Moen knobs.
How to Repair a Wobbly or Loose Kitchen Faucet Base
Move Belongings underneath the Sink
The kitchen sink faucet contains plumbing enclosed in the kitchen cabinets below it. If that area has belongings inside it, remove those possessions and place them in a temporary spot. That protects belongings from accidental damage during repair.
While you’re down there, put on your safety goggles and gloves and clean the area with a damp cloth. This motion picks up dirt and dust. Also, clean the walls and upper surface with a duster or damp cloth.
Turn Off Both Water Supply Valves
As a preventative measure, turn off the hot and cold valves near the water lines. Turn the knobs in a counterclockwise or anticlockwise direction. Pipe bursts and skin burns will occur should something go wrong during installation, and turning it off avoids being soaked from an uncontrollable amount of water.
Locate the Tightening Area with a Flashlight
With nothing blocking your way, get your flashlight, open the cabinet door, and lie on your back to find the nut underneath the loose base. It should be on the roof underneath the base of the faucet. Bring your wrench with you.
Prep the Wrench
As the focus remains on the now-found nut, grab the wrench. It should adjust to the nut’s size so it’s easier to tighten. If you have several, pick the closest one to the nut size.
The flashlight should still be on so you can see it while working.
Use the Adjusted Wrench to Tighten the Hex Nut
The next step requires both hands to interact in tightening the loose nuts. However, the flashlight should still be on to provide proper lighting during the process.
As you use the wrench and hold it tight to the nut, turn it clockwise until it is difficult to turn. This motion tightens an old faucet or a new kitchen faucet. It’s normal to move your body around in awkward positions during this process.
There is a balance between tightening the nut too tight and not enough. A nut not rigid enough is the reason you’re under the cabinet fixing it. A nut too secure stretches it; eventually, this cracks the nut, weakens the nut, damages the pipes, or damages the faucet.
If you don’t have a wrench, tear off a piece of tape and place it nearby. Twist the nut with your finger until it doesn’t twist anymore. Grab the tape and tape it around the nut and the pipes above and below it.
Is The Base of a Kitchen Faucet Secure?
It’s time to get up and check the faucet base’s tightness. It is good news if it doesn’t move. If the faucet still wiggles when you touch it, you must repeat steps three and five until it is.
Turn the Water Supply Clockwise
When you turn the water supply clockwise, you turn the cold and hot water units back on. The water should return to the faucet pipe and sprout with no issue. If you need to adjust the water flow using the water supply knobs, now is the time.
If everything is fine, it will operate like a new faucet, and that’s the best thing because you save money by not hiring a pro to fix it.
Return Your Belongings to the Cabinet
The last thing to do is to retrieve belongings removed from the cabinet and return them to where they were.
Instructions for Repairing a Wobbly or Loose Kitchen Faucet Handle
Turn Off the Water Supply Valves
Near the water supply lines underneath the sink cabinet are the water valves for cold and hot water. While nothing may happen, it’s a good idea to turn off the valves anyway as a preventative measure. If there are items for storage, move them to another location so you can find and turn off the valves.
Take Off the Loose Handle Cap
Place a knife or a tip of a flat-head screwdriver underneath the edge of the cap at the top of the faucet handle. Pop off the protective layer to uncover the type of screw at the base of the handle. One of two screws will be underneath: a hex head set screw or a Phillips head screw.
Be sure to cover an open basin drain because you don’t want the cap to fall into the sink.
Tighten the Loose Screws
Depending on the type of faucet handle screw, grab the necessary tools to tighten it. If it is a Phillips or flathead screw, use a Phillips or flathead screwdriver. If it is a hex screw, you grab a hex wrench.
For a screw, place the screwdriver on top of the loose screw and twist the screwdriver clockwise. For the hex set screw, use the Allen key or one of the other wrenches listed for faucet handles. Just stick the wrench in the screw and turn it clockwise.
Inspect the Handle and Install the Cap
The handle of a kitchen faucet should be sturdy. Therefore, inspect the handles to ensure it is not moving. Of course, the handles must twist on and off, but they should not move in any other direction.
If the working area is satisfactory, it’s time to reinstall the cap. It should fit securely.
Turn on the Water Supply
The good thing about this step is it is the final step. Open the cabinet under the sink and turn on the cold and hot water knobs clockwise. Return all items moved from the cabinet back into the cabinet.
- About the Author
- Latest Articles
Tonya Dobson, Senior Writer
Eleven years of writing experience and counting, Tonya is a master of the home, especially in the home improvement and interior design area. She continues to earn our respect and gets positive reviews from our readers for her writing style on all things for the home. Before her writing career, she interned at Reflect and Refresh. When she is not writing about the home space, you will find her exercising, working on Sudoku puzzles, and enjoying the outdoors.
— She does request privacy. A partial image is provided.